The road marking process can be divided into two types of marking; pre-marking and permanent marking. The permanent markings, using resilient materials such as thermoplastic resin, need to be 100% accurate when applied. Otherwise, removing and re-arranging painted lines will drive up costs and project execution time. This is why pre-marking is necessary.
The pre-marking process has been a manual process for a long time, requiring land surveying skills to stake out the lines using GPS rods and/or total stations. For a new highway section, many lines need to be accurately marked down to a few centimeters’ precision and sometimes even below that. A new stretch of highway including several lanes and different line types can easily take several days to set out, often leading to mental and physical fatigue for surveyors.
Once the road marking positions have been staked out by surveyors, road marking crews often need to extend the lines using strings, tape measures and spray cans so that it is absolutely clear where the permanent markings are to be painted.
Positioning and painting the pre-marked lines can also be done automatically, using a road marking robot for pre-marking. The design of the road markings (position, line type, line length, intervals etc.) is typically already determined in the design phase and is available as two- or three-dimensional data. This is very often a DWG file which contains all the necessary information to place the lines. The robot is able to use this data and mark out the lines using the attached spray can.
Of all the standard driving safety devices—seat belts, air bags, antilock brakes—one thing that many of us likely take for granted is the road markings that help keep cars away from other vehicles on the straight and narrow as well as the curvy and treacherous.
The familiar bright white or yellow lines are made from coating materials that juggle two priorities: drying time and durability. Minimizing drying time, of course, is critical for reducing traffic interruptions. Durability is essential for surviving constant sunlight, in particular ultraviolet radiation, as well as temperature fluctuations, road flexing, and physical abuse from vehicles, says David S. Entrekin, technical director for Future Labs, which tests highway safety products.
There are three classes of road-marking coatings, all of which use similar pigments. White markings typically contain titanium dioxide. Yellow lane lines were historically colored with lead chromate, but the pigment has been phased out for toxicity reasons. A big challenge for manufacturers of road-marking material has been to develop pigments that effectively mimic lead chromate’s color and stability to withstand high-temperature application methods and daily exposure to UV light, says Fred Gelfant, vice president of research and development at Epoplex. As such, firms in the road-marking industry don’t divulge their formulas for yellow paint, except to say that the color comes from organic molecules.
The pigment needs to be applied to the road by means of a quick-drying, liquid medium that must go on as thinly as possible—typically less than 1 mm thick—while also being long-lasting. On the least durable end is latex paint, which lasts only a year or two. Akin to latex paint used for building exteriors, road paint contains pigment, a polymer resin—often an acrylic—and water for the solvent. As the water evaporates, the paint dries and the polymer coalesces.
A second class of road markings is the so-called plural-component materials, which start out separately as a polymer resin and a catalyst; one popular combination is an epoxy and an amine. To apply plural-component markings, the materials must be heated to about 40 to 60 ºC, mixed to start cross-linking, and sprayed onto the road. As the material hits the surface, cross-linking proceeds and the material hardens in 15 to 30 minutes.
Another plural-component combination is polyureas, which mix an amine resin with an isocyanate catalyst. Polyureas cure very quickly—within two to three minutes—and they last about four years. But the downside is that a clean road, which is required for laying down all pavement markings, is particularly important for ureas, says Jerry Britt, technical services manager at Ennis Traffic Safety Solutions.
A third main class of road markings is the thermoplastics, which were originally developed during World War II as a way to circumvent solvent shortages, Britt says. Thermoplastic resins are typically based on modified esters from gum or tall-oil rosins or aliphatic C5 synthetic hydrocarbons. Thermoplastics must be heated to upward of 200 ºC for road application and can be sprayed on pavement or extruded as a ribbon. They solidify almost instantaneously and traffic disruptions are minimal. Applied 1 mm thick, thermoplastic markings last about three years. Applied up to 3 mm thick, they take longer to dry but last for five years.
In addition to spraying or extruding coatings, preformed thermoplastic or polymer tapes can be used for lane lines, crosswalks, or markings such as turn-lane arrows. Thermoplastic tapes are heated with a propane torch to get the tape to melt and fuse with the road, while polymer tapes have a pressure-sensitive adhesive. Some tapes are designed to be temporary but others can last as long as five or more years.
In and of themselves, none of the paint, plural-component, or thermoplastic road markings will shine brightly in a car’s headlights at night. Reflectivity—or, technically, retroreflectivity, which involves reflecting light back close to the source with little scattering—is achieved by dropping glass spheres onto road markings after the markings are applied but before they dry. The spheres are made of sodium silicate glass and typically have diameters between 180 and 850 µm. In the case of thick thermoplastics, spheres are also mixed into the material so that as the coating wears down over several years, new spheres are exposed.
The so-called rainy night problem, when road markings are most difficult to see, presents an additional challenge for road-marking developers. One solution is to apply thermoplastics as bumpy rather than smooth lines, so drivers notice a noise or vibration if they stray out of their lane. A step beyond bumps is to add to the coating little spikes that stick up above water on the road to better reflect headlights. 3M, which also makes road-marking tapes, has developed a new type of reflective element that reflects under water, Entrekin says.
Which materials get used on which roads depends on several factors: weather, traffic volume, impact of shutting down the road, when a road might be resurfaced, and whether snowplows are likely to scrape off a thick coating. A durable but slow-setting epoxy could be attractive for coating 100 miles of highway in Montana but impractical for a busy Los Angeles freeway, for example. It also wouldn’t make sense to pay for an expensive, long-lasting thermoplastic if it will just be decimated by a snowplow or if the road will be resurfaced within a year or two. These are just some of the many considerations evaluated for markings that most drivers simply pass right by.